*NEW* MESSERSCHMITT BF 109F-3 (60") 3D Printed RC 3dLabPrint Model Airplane Kit

Description

I will print in Silver, any and all questions are welcome.  I can print any plane from 3DLabPrint
I need 3-6 days to print and ship out, if not in stock
These models come with a PDF file for decals
General specifications:
Wingspan: 1530 mm / 60 inch
Length: 1260 mm / 50 inch
Height: 478 mm / 18,8 inch
Wing area: 34 dm2 / 3.7 sq ft
Wing loading: 88.8 g/dm2 / 29.7 oz at sq ft
Center of gravity: 72mm / 2.835 in from LE
Airfoil: 3DLabPrint semi 04
Weight of printed parts (w/o wheels): 1493 g / 52.1 oz
Takeoff weight (6s 3300mAh Li-Pol): 3020 g / 106.5 oz
Max takeoff weight: 3200 g / 112 oz
Never exceed speed, Vne: 140 km/h / 87 mph
Design max maneuvering speed, Va: 85 km/h / 52 mph
Stall speed Vs: 31 km/h / 19mph
Performance measurement:
Max speed VH (level flight): 125 km/h – 77.6mph
Rate of climb: 22 m/s (7200 ft/min)
Flight time (6s 3300mAh): 7:00 min (+30% reserve)
Includes:
all 3Dprinted parts for model
Printed user guide
You’ll need to provide:
CA Glue - medium or similar medium viscosity CA glue
Activator for CA Glue or similar, (gas presurized works better)
Soldering Iron or any hot tool
10/500mm carbon tube
1.75-2mm rod/axle for flap hinge (we use fillament or toothpick)
1x Ball Pen Spring
1x 3.5/20mm self-tapping screws
1.2mm steel wire for rudder and elevator linkage
8x micro size servo (you will need 4-8 servos) or similar
light servo 400mm extension cables
1.2 mm /16AWG steel pushrod wires
use also as a hook for cables running through the tunnels...
torch or lighter (to heat up the wire) for servo instaling
Wire cutter, Z bend pliers or just pliers.
some gauge (f.e. ruler) or just pen for marking
Light Foam Main Wheel or any similar 70-80mm
Printed Tail Wheel or any similar 35-40mm
Servoless Retract 44mm x 41mm
or Servoless Retract 44mm x 41mm
8x 3.5-4/30mm self-tapping screw
2x Servo Lead Extension
A:Oleo Legs
Alloy 130mm Straight Mains Oleo Strut
B: 5mm DIY
5 mm wire/rod for LG leg
Landing Gear Wheel Stop Set Collar
8x 3.5-4/30mm self-tapping screw
Dremell or any steel handsaw
Table Vice and Hammer, Yeah!
Torch or lighter
soldering airon etc., shrink tube, servo cable, 4mm connectors.
velcro + velcro strap or battery strap (glue into fuselage)
4x 3mm screw and nuts (motor mount)
Motor: 5055 430KV , or any 5055 430 - 380grams motor (for 6s setup)
ESC: 80A 6s with UBEC or any 6s 60-100A + conector suitable for battery.
Battery: 3300mAh 6S or any 6s (500-600g)
Propeller: three blade 15“x8“, 14“x8“ or use printed one
your R/C system,
adhesive velcro strip for Li-Pol battery, ESC and Receiver
battery strap (glue properly into fuselage)
More details for the model can be found at 3d LabPrint's website: www.3dlabprint
Returns:
If you're not happy with the model I will accept returns as long as it's complete, and totally unassembled. If there's damage during shipping I will send you the parts you need free of charge. Also if you have a hard landing and need replacement parts, just contact me and i can get you a quote for the parts you may need.